Let me tell you a story. The story of how one girl, who in the past would never have considered going near the pipes under the sink, successfully installed a washing machine. That girl is me. I’m Eleanor, nice to meet you.
If you can assemble Ikea furniture successfully, you can definitely plumb in a washing machine. I speak from experience; I’ve put together a lot of BILLY bookcases in my lifetime.
The Key Steps
There are really only five main steps involved (for UK machines).
- Remove the transit bolts.
- Attach the fill hose.
- Attach the drain hose.
- Check the machine does not rock – level it if required.
- Plug in and switch on.
In the past words like “transit bolts” and “drain hose” may as well have been in a different language, but working with our engineers has taught me well. Now (with my firsthand experience fresh in my mind) I can teach you.
It really is easy, I promise.
You Will Need…
For installing my Whirlpool washing machine all I needed was one spanner. It was a 10mm spanner, the second smallest one from this set I own. Some steps also involved tilting the machine, for which I enlisted the help of my boyfriend. But for the most part the installation was a one woman job.
Step by Step Guide to Installing a Washing Machine
These are the specific steps involved in plumbing in my Whirlpool washer. Your washing machine may be a little different, but the key steps I mentioned above are pretty standard for UK models.
Have a flick through the manual
The installation manual that came with my machine was really useful. The instructions were easy to follow for someone who had never installed a washing machine before and in all honesty I would probably have made a mistake without them.
If you have any pride about completing the job without “help”, swallow it I say!
(Doughnut is optional, but go on, you deserve it).
Remove the transit bolts
Transit bolts stop your washing machine from being damaged when it’s transported. Leave them in the machine and you’re gonna have a bad time. Think washing machine bouncing around violently, possibly damaging itself or your kitchen worktops.
Enter your spanner! Unscrew the bolts, remove them and keep them. You can pop them in a bag and tie it to the back of the machine for safekeeping. The man who delivered my machine let me know that some manufacturers require the bolts to be kept for the warranty to be valid.
Remove the bolt casings from inside the machine
When I removed the transit bolts, the blue plastic casings covering them fell down inside the machine. I wasn’t worried. I’d read the manual which informed me this was normal.
Three of the bolts were easy to find and remove, but I did have to trust my boyfriend with my life for the fourth. He tilted the machine and I put my head underneath it so I could peer around with a torch to locate the fourth bolt.
I found it and wasn’t decapitated. Double result.
Cover the transit bolt holes
Supplied with my machine were little plastic covers to be placed over the holes left by the transit bolts, presumably to stop dust and dirt getting into the machine.
Install the base of the washing machine
There was a corrugated plastic base to be fitted once the transit bolt casings had been removed. This was easy to fit. It just needed aligning and securing with some small plastic bolts that came with the machine.
Attach the fill hose to the washing machine
The fill hose lets water flow into the washing machine. I screwed it onto the machine firmly with my hand, not a tool, to avoid over tightening.
Attach the fill hose under the sink
Under my sink there’s the tap that supplies clean water to my washing machine, turned off to prevent leaking. I screwed the fill hose to the tap (which was a little fiddly to line up at first, but I stayed determined).
Turn on the water
Then I just needed to twist the blue switch on the water tap to turn on the water supply to the washing machine. There was a brief sound of running water as the hose was filled.
Remove the cap from the drain pipe and attach the drain hose
The drain pipe under the sink has a cap which stops it from leaking. I removed this so that my machine could drain freely. Push the drain hose onto the drain pipe firmly (using your hands not tools as before).
Keep the drain cap safe
I’ve Sellotaped my cap to the drain pipe under the sink so I can find it and replace it when I move house.
Level the machine, plug in and switch on
My tiles were even enough that my washing machine didn’t wobble, but I gave it a good shake to make sure. If your floor is uneven, screw or unscrew the feet at the base of your washer as necessary to level it. A wobbly machine can damage itself as it shakes and spins. Then plug in and you’re good to go!
Celebrate with a test wash!
Run a hot wash cycle to flush out any dirt in the machine and to check it’s running with no issues.
Everything good? Pat yourself on the back and enjoy feeling like a boss. Also boast to your housemates. I certainly did.
Now go right ahead and get stuck into reading that manual! There’ll be plenty of handy tips about getting the best washing results and guides for common problems inside.
The Alternative to Plumbing In Your Machine Yourself
When we bought our new washing machine my definitely not DIY savvy boyfriend suggested we just let the delivery men install it for us. The idea! Luckily I am a strong independent woman who don’t need no man to help with washing machine plumbing. (Except with the tilting.)
Hopefully I’ve convinced you that that £25 belongs in your purse/wallet instead.
Show Don’t Tell
Oh, one last thing. As well as reading the manual that came with the washing machine, I also recommend watching this video. Especially if you’re the type who finds it easier to watch other people do something than read instructions.
Any questions? Hit me up in the comments.